BIGTREETECH Octopus V1.1 32bit Control Board + TFT35 E3 V3.0.1 Touch Screen Display + 8xTMC2209 V1.2 Stepper Motor Driver DIY for Voron V2.4 3D Printer Controller Board Support Klipper Raspberry PiBIGTREETECH
3 ratingsMore info 1
- ⭐SUPER PERFORMANCE CHIP: BIGTREETECH Octopus control adopts 32-bit ARM-level Cortex-M4 series STM32F446ZET6 chip with a frequency of up to 180MHz, and supports 8 stepper motors. Equipped with highly modular open source firmware Marlin2.0, which greatly improves the overall performance of the motherboard, and all the functions of the motherboard do not require any expansion modules, and supports running Klipper and Marlin firmware
- ⭐SUPER MULTI-FUNCTION CONTROL PANEL: Support material interruption detection, continuous printing after power failure, shutdown after printing, BL_Touch, support online printing, etc. Upgrading the configuration firmware through the SD card, the operation is simple, convenient and efficient. Using high-performance MOSFET, the heat dissipation effect is better.
- ⭐MULTI-FUNCTION DISPLAY: TFT35 E3 V3.0.1 touch screen has higher compatibility. You can choose two working modes: UART serial screen mode and 12864 screen mode. The WIFI port is reserved, and the WIFI function is implemented by an external WIFI module.SD card update firmware is simple and convenient, download from our github, copy and save to SD card
- ⭐ULTRA-QUIET DRIVER: TMC2209 v1.2 with SpreadCycle technology, enables high precision cycle-by-cycle current control for the highest dynamic motion. Large area thermal pad to reduce the temperature of the drive during operation. The motor is difficult to lose step. Can prevent motor vibration. The module supports STEP/DIR and UART modes.
- ⭐WORRY-FREE AFTER-SALES SERVICE: Do you have any questions? Or if you have any problems that need to be solved, please feel free to contact us, and we will arrange the most professional technical team to solve it for you until you are satisfied.
Bigtreetech Direct Octopus V1.1 Control Board 32Bit Silent Motherboard 8 Stepper Drivers Support Running Klipper and Marlin 3D PrinterBIGTREETECH Direct
30 ratingsMore info 2
- 🐙【Main Control Chip】: BIGTREETECH Octopus V1.1 motherboard adoptes ARM Cortex-M4 series STM32F446ZET6 32-bit microcontroller at 180MHz with 512Kb flash ROM. Notice: Input voltage only supports 24V, 12V is not allowed.
- 🐙【CAN BUS】BTT Octopus control board supports CAN Bus connectivity using an ethernet connector. This CAN Bus connection allows to expand control board with other expansion boards very easily.
- 🐙【6 PWM Fans Plus 2 】The Octopus Mainboard offers up to 6 controllable PWM fans and additional 2 without control with the possibility of voltage selection from 5V, 12V or 24V.The BTT Octopus also has 8 sockets for drivers, making it an ideal electronics for demanding machines.
- 🐙【Supports Klipper/Marlin】BTT Octopus supports running Klipper and Marlin.Supports firmware update by USB (recommended) and DFU mode(advanced users). Updating via DFU mode is to send firmware to the board directly from PC with no need for bootloader, which is not recommended for novice users.
- 🐙【Online/ Offline printing】Supports “print from SD card” and “print via USB OTG” using the integrated USB-A port. USB-C interface supports an emulated serial port that allows printing via USB.If you need any help regarding BTT Octopus V1.1 control board, please feel free to contact us via Amazon message. We have professional tech supports online to take care of your problems.
BIGTREETECH SKR 3 Mute Silent Board Motherboard 32bit SKR 2 New Upgrade Controller Board Support TMC2209 TMC2208 A4988 Drivers Compatible with TFT LCD Display FDM 3D Printers DIY MainboardBIQU
29 ratingsMore info 3
- 🍀【New Upgrade of SKR 2】BIGTREETECH SKR 3 mainboard is the upgrade version of SKR 2. Its processor is upgraded to 32-bit 480MHz ARM Cortex-M7 series STM32H743VIT6.The running speed and printing accuracy of SKR 3 controller is greatly increased by 30%+ while its working noise become lower.
- 🍀【Robust Power System】SKR 3 controller board is equipped with TPS5450-5A power chip, which supports power input of DC12/24V and output current of 5A (peak output 6A ). With its robust power system, SKR 3 motherboard can firmly will be the perfect supporter for your Raspberry PI.
- 🍀【DIY Friendly Interfaces】BOOT0 is added for programming firmware in DFU mode. WIFI module (ESP-12S, ESP-07S, ESP32) enables you to easily debug RRF. SKR 3 motherboard also supports bltouch, resume printing function, RGB lights, blocking detection and shutdown after printing function. What’s more, it’s also compatible with TFT35 E3 V3.0/TFT35 V3.0/TFT28 V3.0/12864 LCD display as well as TMC2209, TMC2208, TMC5150, DRV8825 stepper motor drivers.
- 🍀【Thermistor Protection Design】Adding protection circuit for the thermistor to avoid burning of main control chip caused by hot bed or heater creepage. The resistance value of thermistor of SKR 3 also supports PT1000 by wire jumper to select pull-up resistance value. In this way, it’s convenient for DIY by eliminating the connection of external module.
- 🍀【About Firmware】SKR 3 mainboard is directly compatible with Marlin and Klipper firmware (RepRapFirmware need to debug first). Firstly download firmware on GitHub website of name “firmware.bin", copy and save it to SD card, firmware must bed reserved, then re-plug the SD card and wait to 10s. When the status indicator stops flashing and the file name in the Micro SD card is renamed to "FIRMWARE.CUR" then update sucessfully. Note: Our control board come without SD card.
BIGTREETECH SKR Mini E3 V2.0 Control Board 32-Bit Silent Motherboard Integrated with TMC2209 UART Stepper Motor Driver for Upgraded Ender 3 3D PrinterBIGTREETECH Origianl
507 ratingsMore info 4
- 🌈【Silent Control Board】BTT SKR MINI E3 V2.0 adopts ARM Cortex-M3 series STM32F103RCT6 main control chip with 32-bit CPU 72MHz, integrated with TMC2209 to enhance its stability. It's a super easy drop in replacement for Ender 3 printer.
- 🌈【Better Thermal Dissipation】The hot-bed MOS tube uses WSK220N04, low on-resistance, which reduces heat generation. Enlarged heat dissipation area protects driving chip and components from problems caused by heat sink.
- 🌈【Support Various Functions】BTT SKR MINI E3 V2.0 supports various function extensions, such as, BLtouch, filament detection, resumption of shutdown, shutdown after shutdown, etc .
- 🌈【 4 Layers for Board】Bigtreetech SKR MINI E3 V2.0 increased to 4 layers on the control board's back, so as to improve on heat dissipation signal function and anti-interference.
- 🌈【Satisfying Customer Services】If you need any information for SKR MINI E3 V2.0, you could contact us on Amazon, and we'll get back to you within 24 hours.
BIGTREETECH SKR Pro v1.2 32bit Control Board high-Frequency 3D Printer Motherboard, Support TMC5160, TMC2208, TMC2130, TFT28, TFT32, TFT35, 12864LCD ect.BIGTREETECH
131 ratingsMore info 5
- The main control uses the ARM-level Cortex-M4 series with a 32-bit dominant frequency of 168 MHz STM32F407ZGT6 chip, performance is greatly improved.
- Equipped with highly modular open source firmware Marlin2.0, it is convenient for users to DIY and further-development, to avoid the worry of not being able to master the core code.
- Motor driver support :TMC2209,TMC2208,TMC5160,TMC2130,ST820,LV8729, DRV8825,A4988, etc.Display screen support: BIGTREETECH- 2.8 inch TFT,BIGTREETECH-3.5 inch TFT, LCD2004,LCD12864.
- Support Serial WIFI Online Printing. 6 motor drives, 3 extruders, 3 CNC fans. Reserve extended ports of BL Touch, PWM, ADC, UART, I2C and SPI;Support power-off continuous printing, material cut detection, shutdown and other functions;Support for dual Z axis printers (series dual Z.
- If you encounter any problems, please contact us via Amazon as soon as possible. We have professional technical after-sales personnel to solve your problems;
Adjustable DC Power Voltage Converter, MYSWEETY AC 110V-220V to DC 0-48V Module Switching Power Supply Digital Display 480W Voltage Regulator Transformer Built in Cooling FanMysweety
334 ratingsMore info 6
- ✅Input voltage range is AC110-220V, output voltage range is DC 0-48V adjustable, output current can't be adjusted and it is up to your load, maximum output current is 10A, so this item will not fit for your device with over 10A current.
- ✅LED display shows you real-time voltage, which makes it more convenient for you to adjust voltage. Case Material: Metal; Main Color: Silver Tone. Widely used in Industrial automation, Radio, Broadcasting, LED display, communications, Security cameras, Lighting, Computer.
- ✅Equipped with temperature control cooling fan: it will automatically operate when this power converter need to be cooled without any noise.
- ✅Protection Function: over load protection, over voltage protection, short circuit protection, this protection will protect your load well. 🔺NOTE: before using, please select the input voltage 110V/220V according to your local voltage, to avoid damaging, switch is at right side of the item.
- ✅Special Atention: Do not work with overload. No switching power supply can be loaded with full current for a long time, and the long-term load cannot exceed 80% of the rated current. If you use inductive loads such as motors, fans, etc., please pay attention to the parameters of the motor's maximum starting current and locked-rotor current. This parameter should not be higher than the maximum current of the power supply, otherwise it may cause damage to the power supply.
Newest SKR Mini E3 V2.0 32Bit Control Board Integrated with TMC2209 UART Driver Upgrade SKR Mini E3 V1.2 for 3D Printer Parts for Ender 3 V2.0 3D Printer(firmware Install for Ender 3)BIQU
773 ratingsMore info 7
- 💐【32 Bit High Performance Microprocessor】SKR MIN E3 V2.0 is a silent control board adopts 32 bit ARM level Cortex-M3 series STM32F103RCT6,72MHz frequency Microprocessor, which is designed for ENDER 3 3D printer particularly,a perfect replacement motherboard of the Ender3 printer.
- 💐【Support a variety of Functions】SKR MINI E3 board supports BLTouch, RGB lights, blocking detection, shutdown function.What ’s more,it also supports TFT35 E3 V3.0,TFT35 V3.0,TFT28 V3.0 touch screen,original 12864LCD of Ender 3 printer.
- 💐【Firmware Update】Firstly download firmware of SKR MINI E3 V2.0 motherboard,copy and save it to SD card.firmware must bed reserved ,then re-plug the SD card and wait to 10s.The firmware has been successfully updated.
- 💐【Ultra-Silent TMC2209 V1.2 Driver】Integrating with TMC2209 Ultra-silent motor driver,use StealthChop2 ultra-quiet technology which reduce stepper sound,super quiet and smooth.
- 💐【Advantages of using TMC2209 Drivers】TMC2209 drivers with excellent heat dissipation,it can lower the temperature when drive is working.Also, it can prevent the motor from shaking as well as it is difficult to lose steps.
BIGTREETECH 3D Printer Upgrade Motherboard Octopus V1.1 Control Board 32bit Compatible TMC2209, TMC2208 Driver, Support DIY Klipper Firmware and Raspberry Pi Online Printing for Voron V2.4 3D PrinterBIGTREETECH
116 ratingsMore info 8
- 【Main Control Chip】Uses a 32-bit ARM Cortex-M4 series STM32F446ZET6 main control chip with a core frequency of 180MHz.
- 【Strong DIY Support】This motherboard supports up to 8 stepper drivers with 9 stepper driver outputs in total; And up to 6 PWM fans and 2 always-on fans with the ability to individually select the voltage rail that will drive each fan. Select from Vin, 12V or 5V.
- 【Realize Online Printing】Interfaces with a Raspberry Pi using emulated serial over USB or direct UART to any of the serial ports on the board, to realize Klipper Firmware and Raspberry Pi Online Printing.
- 【Motherboard Expansion Function】Support BLTouch, locked-rotor detection, shutdown after printing, resume printing after power failure, CAN bus, U disk function, IIC expansion; at the same time reserved WIFI interface, PT100 thermistor interface (optional, Only reserved interfaces, customers need to purchase chip welding, please pay attention.), dual Z-axis printer.
- 【Increase Protection Function】Uses high-performance MOSFETs to increase heating efficiency while also reducing heat generation on the motherboard. Supports “print from SD card” and “print via USB OTG” using the integrated USB-A port.
BIGTREETECH SKR Mini E3 V3.0 Control Board +TFT35 E3 V3.0.1 Touch Screen 32-Bit Silent Motherboard Integrated with TMC2209 UART Stepper Driver Compatible with Ender 3 Pro/5 3D PrinterBIGTREETECH
35 ratingsMore info 9
- ⭐【BIGTREETECH Combo Set】Comes with Bigtreetech SKR Mini E3 V3.0 control board and TFT35 E3 V3.0.1 touchscreen with dual modes as a set. Adopted the latest G0 series MCU-STM32G0B0RET6 main control chip packing excellent performances.
- ⭐【Upgraded More Capabilities】Intergrated with TMC2209 mute stepper driver, BIGTREETECH SKR Mini E3 V3.0 control board offers silent performance as default, and supports dual Z steppers for linear rail and belt upgrades, filament runout support, automatic shutdown (UPS support), power-off resume, sensorless homing and so on.
- ⭐【Impressive Heat Dissipation】The SKR MINI E3 V3.0 also looks aesthetic with upgraded designs.New heatsink and 3 PWM controlled fans serve to cool down the machine during printing, effectively improving performances on heat dissipation. A direct 3D printer control board replacement for Ender 3, Ender 3 Pro, and Ender 5 motherboards.
- ⭐【Supports Touch/Graphic Display】TFT35 E3 V3.0.1 touch screen enables you to easily switch between the Marlin LCD emulator and touch screen with menu interface, simply by pressing and holding the selector wheel. It's a plug and play on Ender series printers with BTT SKR MINI E3 V3.0 control board.
- ⭐【Satisfying After-Sales Support】If you have any problems about BTT SKR MINI E3 V3.0 & TFT35 E3 V3.0.1 smart display combo sets, please feel free to contact us anytime. We have profession technical supports team to help you as soon as we can.
BIGTREETECH Octopus Pro V1.0 32Bit Control Board Compatible TFT Screens/LCD2004/LCD12864 Supports 8 Stepper Drivers 60V Stepper Motor Klipper RRF and Marlin 3D Printer BoardBIGTREETECH
31 ratingsMore info 10
- 🐙【High Performance Chipset】:BIGTREETECH Octopus V1.0 pro control board F446 version uses 32-bit ARM-level Cortex-M4 series STM32F446ZET6 main chipset with a frequency of up to 180MHz,and 563k of flash memory, being the most advisable for Klipper or Marlin firmwares.
- 🐙【Supports Multiple BUS】:BTT Octopus V1.0 Pro 32-bit control board supports CAN BUS via 6P6C RJ11 connector for future expansion modules,SPI BUS expansion port for SPI modules such as MAX31865, and I2C BUS expansion port for I2C modules.
- 🐙【6 PWN Fans Plus 2】:Comes with 6 controllable fans, and two normally open fans, which all supports power supply voltage range from Vin, 12V, and 5V. Protection against shorts in the fan sockets effectively prevents FETS from damages caused by turning on/ off the fans.
- 🐙【Update Firmware via USB/DFU】:Firmware Updating by USB and DFU mode are available. Updating it through DFU will allow us to upload the firmware or bootloader in case the normal process does not work while using USB-C cables, which is NOT recommended for novice users.
- 🐙【Satisfying After-Sales Services】:One-Year warranty is 100% assured. If you have any questions about BIGTREETECH Octopus pro 3D printer control board, please feel free to contact us via Amazon. Our professional technical group will take care of your problems.